阅读中文 →

What Is Mattress Support Factor? Understanding Indentation Load, Compression and Resilience (2026)

By Nancy Yu (B2B Business Director) | Updated 2026-11-10

Key Takeaway

Support factor is the ratio of a material's load at 65% indentation to its load at 25% indentation (often written as 65%-ILD ÷ 25%-ILD).

Key Takeaways
  • ILD stands for Indentation Load Deflection; IFD (Indentation Force Deflection) is the same concept under slightly different…
  • Support factor (sometimes called compression modulus ratio) is the ratio:
  • Firmness, as a sleeper experiences it, is a compound of several things:
  • Foam and fiber slabs are characterized by indentation methods; whole mattresses are assessed by different, often…
  • This is the most important caveat for any R&D or procurement buyer.

Direct Answer:

Support factor is the ratio of a material's load at 65% indentation to its load at 25% indentation (often written as 65%-ILD ÷ 25%-ILD). A higher ratio means the material becomes progressively firmer as it compresses—giving soft initial comfort but firmer deep support. It is a derived value from ILD/IFD testing, not a single measured "firmness," and it must be read within one test standard and one lab condition to mean anything.

Key Takeaways

  • ILD (Indentation Load Deflection) / IFD (Indentation Force Deflection) is the force needed to compress a material to a set percentage of its height.
  • The 25% ILD is the common "firmness" reference; the 65% ILD measures deeper compression resistance.
  • Support factor = 65%-ILD ÷ 25%-ILD. Higher = more progressive (soft-to-firm) support.
  • Firmness is only partly captured by ILD; feel also depends on construction, thickness, and quilting.
  • Foam is tested by ASTM D3574 / ISO 3386; whole mattresses use methods like EN 1957 rollator durability.
  • Never compare ILD numbers from different labs, platens, preconditioning, or materials as if equal.
  • For B2B/OEM, specify ILD, support factor, and test method together on the spec sheet.

What Is ILD / IFD?

ILD stands for Indentation Load Deflection; IFD (Indentation Force Deflection) is the same concept under slightly different naming in some standards. Both describe how much force, in pounds (or newtons), is required to compress a sample to a defined percentage of its original thickness.

The classic measurement compresses a circular platen into a foam slab:

  • 25% ILD: The force to indent the material to 25% of its height. This is the value most often quoted as "firmness."
  • 65% ILD: The force to indent to 65% of height. This reflects how much the material resists bottoming out.

A typical latex or polyurethane sample might show a 25% ILD around 25–40 lb and a 65% ILD around 60–110 lb, but those absolute figures depend entirely on how the test was run. ILD is a material property of the layer being tested, not of the finished mattress as a whole.

What Is Support Factor?

Support factor (sometimes called compression modulus ratio) is the ratio:

Support Factor = 65%-ILD ÷ 25%-ILD

If a foam shows 30 lb at 25% and 90 lb at 65%, the support factor is 3.0. A low support factor (near 2.0) means the material feels roughly the same as you sink in—uniform and less "progressive." A higher support factor (2.5–3.5+ for many latex and high-resilience foams) means the material stays soft near the surface but firms up noticeably under deeper load.

Why this matters for sleep products: a higher support factor helps a mattress feel cushioned on first contact yet supportive for heavier body zones (hips, shoulders). It is a useful single number for comparing two materials tested the same way—not for comparing materials tested differently.

How Firmness Is (and Isn't) Measured

Firmness, as a sleeper experiences it, is a compound of several things:

  • The ILD/IFD of the comfort layer
  • The ILD/IFD and thickness of support layers
  • The spring system (in pocket-spring or Bonnell builds)
  • Quilting, ticking, and the compression of natural fibers like wool or horsehair
  • The sleeper's weight, sleeping position, and temperature

This is why a single ILD number can mislead. Two mattresses with the same 25% ILD can feel very different because of layer order, thickness, and the presence of springs or natural padding. ILD tells you about one layer's resistance at one compression; it does not tell you the whole-bed feel. Support factor adds a second dimension—how that resistance changes with depth—but it still describes the layer, not the assembled product.

The Indentation Test Method

Foam and fiber slabs are characterized by indentation methods; whole mattresses are assessed by different, often durability-focused methods.

AspectFoam / Layer TestWhole-Mattress Test
Common standardsASTM D3574, ISO 3386EN 1957 (rollator), ASTM F1566
What is measuredILD/IFD at 25% and 65%Durability, hardness, set after rolling
SampleCut slab of materialFinished mattress or topper
Primary outputForce vs. indentation curveLoss of height / hardness over cycles
Support factor useDirect (from ILD ratio)Indirect; not a standard SF output

ASTM D3574 covers flexible cellular materials (polyurethane and similar foams) and includes the indentation force deflection procedure. ISO 3386 addresses indentation hardness of flexible cellular materials as well. For finished mattresses, EN 1957 uses a rollator to simulate long-term use and assess durability and hardness retention; ASTM F1566 provides mattress and foundation durability test methods. These methods answer different questions—foam ILD is about material feel, rollator testing is about how the bed holds up.

Why Numbers Aren't Comparable Across Labs and Standards

This is the most important caveat for any R&D or procurement buyer. Two ILD numbers that look identical on paper can come from entirely different physical realities.

  • Platen size differs. A larger or smaller compression foot changes the contact area and the measured force. A 200 cm² platen is not the same as a 323 cm² platen.
  • Preconditioning differs. Samples may be conditioned at different temperature, humidity, and rest time. Foam and natural fibers both shift with moisture and temperature.
  • Indentation speed and dwell time differ. How fast the platen moves and how long it holds changes the reading, especially for viscoelastic (memory) foams.
  • Sample preparation differs. Cut location, age, and whether the layer is bonded to others all matter.
  • Material type differs. ILD of latex is not directly comparable to ILD of polyurethane, and neither is comparable to the behavior of a pocket-spring or a horsehair pad.

Bottom line: never mix ILD values across different standards, labs, or materials as if they were interchangeable. A 30-lb ILD from Lab A on latex tells you nothing reliable about a 30-lb ILD from Lab B on PU foam. Always pair the number with its method, platen, conditioning, and material.

How to Specify Support Factor for B2B / OEM

For buyers writing a specification or evaluating a supplier, put the measurement context on the same line as the number. A usable spec sheet entry looks like this:

  • Comfort layer: Natural latex, 25% ILD 28 lb, 65% ILD 84 lb (support factor 3.0), per ASTM D3574, platen 323 cm², conditioned 23°C / 50% RH, 24 h.
  • Support core: Pocket spring, gauge and count specified separately; ILD not applicable.
  • Whole-bed validation: EN 1957 rollator, target hardness loss < X% after N cycles.

Request that suppliers state the standard, the platen area, preconditioning, indentation levels, and units. Ask for a support-factor value only when both ILD points come from the same test run. For natural-fiber builds (wool, horsehair, latex), note that ILD may be reported on the component slab, while the finished bed is validated by mattress-level methods—so specify both.

Document a tolerance band (e.g., 25% ILD ± 3 lb) and a re-test cadence for incoming batches. This protects consistency across production and across suites in a hospitality rollout.

Support Factor FAQ

1. What does ILD stand for?

Indentation Load Deflection—the force required to compress a material to a set percentage of its height, usually reported at 25% and 65%.

2. Is ILD the same as firmness?

It is a firmness proxy for a single layer, not the whole-bed feel. Construction, thickness, and springs also shape perceived firmness.

3. What is a good support factor?

Many latex and high-resilience foams fall around 2.5–3.5. Higher means more progressive (soft-to-firm) support; "good" depends on the design target.

4. Can I compare a latex ILD to a polyurethane ILD?

Only if tested under the same standard, platen, and conditioning—and even then, material behavior differs. Do not treat them as equal by number alone.

5. Why do labs report different ILD for the same foam?

Differences in platen size, preconditioning, indentation speed, and sample prep change results. That is why method context must travel with the number.

6. Does support factor apply to pocket-spring mattresses?

Support factor is defined for indentation-tested layers (foam, latex). Spring systems are specified by gauge, count, and zone, not ILD—though a latex comfort layer on top can still carry an ILD/SF value.

7. Which standard covers foam ILD?

ASTM D3574 and ISO 3386 are common for flexible cellular materials; check which your supplier used.

8. How is a whole mattress tested?

Methods like EN 1957 (rollator durability) and ASTM F1566 assess the finished bed's performance and durability rather than a single ILD.

9. Should support factor be on my spec sheet?

Yes, but only alongside the test method, platen, conditioning, and units. A bare ratio is meaningless.

10. Does higher support factor mean firmer?

Not necessarily firmer at the surface—it means the material firms up more as you compress it. Surface feel is set by the 25% ILD.

11. How do natural fibers affect ILD?

Wool and horsehair pads compress and recover differently than foam; ILD is usually reported on component slabs, with the finished bed validated by mattress-level methods.

12. Can BONJOUR LUXE provide tested support specs?

Yes. For B2B and OEM buyers, BONJOUR LUXE can supply tested support specifications—ILD and support factor with stated method and conditions—for natural-latex and hybrid comfort layers.

Sources

  • ASTM D3574 — Standard Test Methods for Flexible Cellular Materials (slab polyurethane foam, including indentation force deflection)
  • ISO 3386 — Indentation hardness of flexible cellular materials
  • EN 1957 — Domestic mattresses: durability assessment by rollator
  • ASTM F1566 — Standard Test Methods for Mattresses
  • ISPA — International Sleep Products Association, material and product guidance
  • OEKO-TEX / GOTS — textile and organic fiber reference standards

Support factor is a powerful, compact way to describe how a mattress layer behaves under increasing load—but only when its ILD inputs come from one test method, one lab condition, and one material. For B2B, OEM, and custom luxury projects, BONJOUR LUXE (佰仕禄®手工床垫), an ISPA member since 2014 based in Keqiao, Shaoxing, Zhejiang, builds hand-tufted, foam-free mattresses from natural latex, wool, and horsehair with pocket-spring options. The team can provide tested support specifications—ILD and support factor with stated standards and conditions—for buyers specifying luxury sleep systems. Contact Nancy Yu (余温) at nancy@bonjourluxe.com or +86-19357569981 to request a specification package.

Frequently Asked Questions

What is mattress support factor?
Support factor is the ratio of a material's load at 65% indentation to its load at 25% indentation (65%-ILD ÷ 25%-ILD). A higher ratio means it grows firmer with deeper compression.
What do ILD and IFD mean?
ILD (Indentation Load Deflection) and IFD (Indentation Force Deflection) describe the force needed to compress a material to a set percentage of its thickness. They are the same concept under different naming.
Does a higher ILD always mean a firmer mattress?
ILD at a single point indicates initial firmness, but overall feel also depends on support factor and layer construction. One number does not define the whole mattress.
Why are ILD numbers not comparable across labs?
Results depend on sample thickness, test standard, temperature and pre-conditioning. Always compare values tested under the same method.
How should buyers specify support factor for OEM orders?
State the target ILD at both 25% and 65% indentation, name the test standard, and set an agreed tolerance in the contract rather than relying on a single firmness claim.
Sleep Academy →

Need a handcrafted natural mattress — or an OEM/ODM partner?

Bonjour Luxe hand-tufts every mattress with horsehair, wool, camel hair and silk — no foam, no glue. Retail customisation and B2B partnership programmes are both available.